Deco can be used with an existing router. Here are two typical connection structures. Topology 1: Note: When Deco works in Router mode, it's not suggested to connect more than 1 deco unit to the existing router directly, as it may cause a network loop.. When Deco works in Access Point mode, it's no problem to connect more than 1 deco unit to the existing router directly.
If you're renting that combined router/modem from a cable Internet provider, there's also another option — you can generally buy your own router to eliminate the router service fee from your monthly cable Internet bills. This doesn't apply to ADSL, fiber, or satellite connections — just cable. Very often, a device called a router sits between the DSL or cable modem and your laptop or the rest of the network. The router (rhymes with chowder) is designed to provide an interface between the Internet and your local network.The router takes care of most of the more confusing networking options for you; plus, it provides firewall protection between the computers on your network and the 1) you need to know witch band is use by you sim carrier and select a antenna compitble to. 2) you need to plug ethernet port of MR1100 to the WAN ethernet port of your powerfull router. The DHCP ip have to be configure to not disturb the DHCP to your powerfull router. You could put your MR1100 in bridge mode or desacte DHCP mode. NOTE: Before you connect a Belkin router to another router, make sure that both routers have different IP addresses. This is necessary to avoid conflict and connectivity issues in the local network if they have similar IP addresses. In this case, you need to change the IP address of the secondary router. Yes, I have my modem hooked up to a router downstairs then have that router hooked up to another router that's upstairs. i7-920 @ 3.6 // 770 GTX // 12 GB G.Skill Sniper Ram // PS3 // 360 FiiO e9+17 // AD700 + M50 // Deck Legend + 82 // DAS Ultimate S NOTE: Before you connect a Linksys router to another router, make sure that both routers have different IP addresses. This is necessary to avoid conflict and connectivity issues in the local network if they have similar IP addresses. In this case, you need to change the IP address of the secondary router. If, for example, you have a router you purchased and a router supplied by your ISP, then you will want to connect to both of them and check what they report as their WAN IPs. Here's an example, via our D-Link router running DD-WRT firmware, of what you're looking for.
NOTE: Before you connect a Belkin router to another router, make sure that both routers have different IP addresses. This is necessary to avoid conflict and connectivity issues in the local network if they have similar IP addresses. In this case, you need to change the IP address of the secondary router.
Thank you for your reply information. I replied via the ATT community forum with a followup question - please check my reply there. My reply basically says that I found the Somejoe messages the other night, and it seem that his solution applies to my case.Basically, I should connect, via ethernet cable, between ATT router 3801 Home Network port jack (but NOT the broadband jack) and the new Deco can be used with an existing router. Here are two typical connection structures. Topology 1: Note: When Deco works in Router mode, it's not suggested to connect more than 1 deco unit to the existing router directly, as it may cause a network loop.. When Deco works in Access Point mode, it's no problem to connect more than 1 deco unit to the existing router directly. We show you how to Boost your Wifi signal by adding another wireless router and connecting the two using a cable.
wirelessly no , but you could look at powerline adapters to connect main router to the orbi . however the orbi is designed to connect the main orbi router to the main router via ethernet and then the sat/s connect back to the orbi router via wifi which achieves the same thing
You can connect to the WiFi network that's being broadcast by your ISP modem or router, or just use a nearby public WiFi network. Connect the ethernet cable from your computer to the WAN port of the router (or in any port if you're using an ethernet switch). This should be a different router or switch than the one from your ISP.